Fan Clutch Tools

This one-piece tool has a specially designed contour for easy use on vehicles using bolt-on water pump pulleys to enable the removal and replacement of the viscous fan clutch. This one-piece tool replaces all designs of water pump holding tools that hold the "bolt on type pulleys". No adjusting or fiddling, simply with only one hand, hook on the pulley bolt and hold to remove the viscous fan clutch... View Details

36mm for Use with PFC440. Faster and easier than conventional fan clutch wrench. No holding wrench necessary. View Details

Two piece kit gives the professional technician the ability to service all fan clutches that have bolt on pulleys on the water pump. Works with Chrysler, GM, Ford, Land Rover and Mazda (Not including the 4.9 liter 6 cylinder Ford). View Details

Opening is 40mm (1.575"). Black oxide coating to resist corrosion. View Details

Quickly remove and install the fan clutch when repairing the water pump or fan clutch. Does the job much faster than conventional fan clutch wrenches. Set includes 7 driving wrenches that fit Ford, GM and Chrysler; 7/8", 32mm, 36mm, 40mm, 47mm, 1-7/8" and 2" in a plastic storage case. View Details

Used to remove and replace thermostatic fan assemblies while eliminating the need for various size holding wrenches. Applications include: Ford trucks with 2.8L, 2.9L, 3.0L, 4.0L, 4.9L and 5.0L engines; Dodge trucks with 3.9L, 5.2L, 5.9L, 8.0L V10 engines; GM trucks with 4.3L, 5.0L and 5.7L engines; Jeeps with 5.2L engines. View Details

Most popular sizes of viscous fan clutch hex couplings are either 36 mm or 48 mm. This double ended wrench was developed to reduce the cost of purchasing two wrenches, which are needed when performing a variety of fan clutch jobs. When the MST9521 is used with MST6160, most Chrysler, Ford, GM & Land Rover applications can be performed on vehicles that have bolt on water pump pulleys. View Details

Positive locking action. Fully adjustable to match a variety of applications. Holds the clutch hub stationary during removal and installation. View Details

For removing both bolt-on and pressed-on pulleys . Includes universal pulley holder and an upgraded version with replacement pins for use with pressed-on pulleys and can also be used for cam sprocket holding and adjustment. Holding wrenches include 22mm, 36mm, 40mm, 47mm and 50mm holding tools and four pin sets from 8mm to 18mm... View Details

7/8" Adapter for PFC43300 Pneumatic Fan Clutch Wrench Kit fits Ford Ranger 3.0L engines, 1993 and newer. View Details

32mm wrench is 17" to reach down to the fan clutch hex coupler. Works on all BMW models. For 3, 5, 7, 8, X and Z Series BMW applications, Audi 1996 and later (except pressed on pulleys) VW 1998 and later (except pressed on pulleys). View Details

36mm wrench. View Details

Specially designed tool is used on vehicles using pressed on pulleys. Billet chromoly bulkhead pins. Used on the following applications:... View Details

Double-sided tool with two pin configurations, two prongs on each side on the other to hold pressed pulleys with holes in place while loosening the fan clutch. Use with a 36mm fan clutch wrench on GM, Chrysler and Jeep truck, van and SUV applications from '99 and on for GM, and '98 and on for Chrysler and Jeep. For GM '99 and newer 4.8L, 5.3L and 6.0L; Chrysler '98 and newer 3.9L, 4.7L, 5.2L, 5.9L and 8.0L; Chrysler factory replacement water pumps '93 and newer 3.9L, 5.2L, 5.9L and '97 and newer 8.0L... View Details