List: $102.45
(0) 4 PIECE HAMMER ACCESSORY KIT
AH4KA

Features four of the most popular air hammer chisels. .401 shank. View Details

List: $34.45
(0) 8" VALVE DRIVE AIR CHISEL
MC395A

Made from silica alloy steel for superior fatigue and flex resistance. Use with .401 parker shank. Designed to remove and install replaceable valve guides. View Details

List: $57.95
(0) 8" HAMMER
MC2318

For U-joints, ball joints and body forming. Black onyx finish for corrosion resistance. Use with .401 Parker shank. View Details

List: $57.95
(0) 1-3/8" - 35MM SEPARATING FORK
MC2448

Separates ball joints and tie rods quickly and easily. .401 parker shank. Minimal shock to the assembly lessens damage to the vehicle. View Details

List: $19.75
(1) 6" PNEUMATIC PUNCH, 1/2" DIAMETER
MC383A

.401 shank. View Details

List: $35.75
(0) 4" U-JOINT AND TIE ROD CHISEL
MC391B

.401 shank. View Details

List: $74.60
(0) 18" HAMMER
MC2418

Extended length design for difficult to access applications. .401 shank. View Details

List: $91.05
(1) TRUCK ANCHOR PIN BUSHING REMOVER / INSTALLER
TAPP288

Pneumatic bushing driver set removes and installs truck leaf spring bushings and trailer anchor pin bushings and stuck anchor pins. Drive the bushing out with the small cone. Use the larger cone to install bushing to the proper depth... View Details

List: $183.95
(0) 5 PIECE THICK PICKLE FORK SET
APF412

Thicker fork design provides extra lift when replacing worn out ball joints, pitman arms and pickup track bars. The set includes five forks: 11/16", 15/16", 1-1/8", 1-7/16" and 1-5/8". Forks are threaded to interchange with either the handle for hammering or the pneumatic driver (.401 shank) and a 6" extension that works with either handle to provide extra reach. View Details

List: $279.95
(0) TEXAS TWISTER AIR HAMMER PULLING KIT
LT855

Convert your air hammer into a pneumatic slide hammer with the Texas Twister. Simply snap the Texas Twister curved air bit into the collet of your hammer with one of the bits attached. Reverse the air hammer handle in your hand using your thumb to push the hammer trigger, generating pulling power from the air hammer... View Details

List: $38.35
(1) 2" WIDE SCRAPER
MC2308

2" blade 8" long wide pneumatic scraper. Removes gaskets, rust, undercoating, paint, floor tile face area. Use with a .401 parker shank. View Details

List: $27.60
(1) 6" TAPER PUNCH, 3/8" POINT
MC2384

6" Long Taper Punch with 3/8" tip. Use for peening and crimping bodies, driving rivets and hinge pins. Made from silicon alloy steel for superior fatigue and flex resistance... View Details

List: $57.90
(1) 2 PIECE HUB REMOVAL SET FOR DODGE PICK UPS
FSH382

Separates the frozen hub assembly from the steering knuckle on Dodge pickups. One is for Dodge 4x4, 3/4 and 1 ton and the other for older Dodge pickups. Tool drives against loosened retaining bolts to separate assembly... View Details

List: $66.20
(0) 18" SCRAPER
MC2918

Extended length designed for difficult-to-access applications. .401 shank. View Details

List: $113.80
(0) SEIZED FASTENER REMOVER KIT
FR18

Use with air hammer to loosen rusted or frozen fasteners and brake rotor screws on most vehicles. Special socket design applies the impact force to the center of the frozen bolt through the nose on the pneumatic driver. Focuses the pneumatic hammering action on the center of the fastener... View Details

List: $45.95
(0) Patented ball peen air hammer chisel with .401 shank
MBP12

Patented ball peen air hammer chisel with .401 shank. Used for removing ball joints, tie rods, motor mounts, etc. View Details

List: $79.95
(0) 2 PIECE BALL PEEN AIR HAMMER KIT
BHP2

Patented 6.5" and 12" long ball peen air hammer chisels. .401 shank. Used for removing ball joints, tie rods, motor mounts, etc. View Details

List: $181.10
(0) OFFSET IMPACT DRIVER SET
LT1800

Offset 15° angle for greater access in tight areas. Recessed, non-turning head well prevents driver from slipping off stud or fastener. Extra-long, extra heavy, non-turning straight hammer won't rotate off stud... View Details

List: $49.65
(0) 6" SMOOTHING HAMMER CHISEL
MC236

1" head diameter for body forming on fenders, hood and panels when used against a body dolly. Great for ball joints and U-joints. View Details

List: $56.90
(0) 1-11/16" X 7" U SEPARATING FORK
MC2449

Separate ball joints and tie rods quickly and easily. .401 parker shank. Minimal shock to the assembly lessens damage to the vehicle. View Details