• FREE SHIPPING OVER $75*

Pullers

LOW-PROFILE PITMAN ARM REMOVER | Matco Tools List: $254.95
(0) LOW-PROFILE PITMAN ARM REMOVER
MST68800A

Replaces previous model MST68800 pitman arm remover. Fits within the confined space on most GM 1988-2000 (and later) C and K chassis trucks and SUVs. Patented design removes pitman arms on 2001 to current model trucks and SUVs equipped with sector shaft type steering gear... View Details

GEAR AND PULLEY PULLER | Matco Tools List: $124.95
(0) GEAR AND PULLEY PULLER
P522

Removes parts with tapped holes, like gears, pulleys, etc. Cap screws up to 1/2" diameter may be used (cap screws NOT included). 2" to 7-3/4" spread range when used with 1/2" diameter cap screws... View Details

REAR AXLE BEARING PULLER SET | Matco Tools List: $79.95
(0) REAR AXLE BEARING PULLER SET
7495

Rear axle bearing puller fits min. bearing tube I.D. of 1" and max axle tube I.D. of 1-7/8". View Details

REAR AXLE BEARING PULLER | Matco Tools List: $79.95
(0) REAR AXLE BEARING PULLER
7497

Fits min. tube I.D of 1-3/8" and Max axle tube I.D of 2-7/8". View Details

PITMAN PULLER SET | Matco Tools List: $313.95
(0) PITMAN PULLER SET
PA3010

Contains three Pitman arm pullers that will remove most automotive and light truck Pitman arms used on today's vehicles. Open puller specifically engineered to remove Pitman arms in low clearance areas found on light trucks and SUVs. View Details

LARGE CONICAL PITMAN ARM PULLER | Matco Tools List: $112.95
(0) LARGE CONICAL PITMAN ARM PULLER
PA150

Designed to fit Pitman arms on domestic cars and light-duty trucks. Conical design fits securely on Pitman arm. 3/4-16 x 4-3/4" forcing screw provides enough power to remove stubborn Pitman arms. View Details

PILOT BEARING PULLER | Matco Tools List: $144.95
(0) PILOT BEARING PULLER
MST1170

Designed for small diameter internal pulling applications. 3/4" reach with a minimum diameter of 1/2" with a maximum spread of 1-1/2". Great for pulling flywheel pilot bearings on automobiles, trucks and tractors... View Details

LARGE CROSS BLOCK | Matco Tools List: $60.95
(0) LARGE CROSS BLOCK
4534A-1

Cross block. Length: 180mm. View Details

LARGE ADJUSTING YOKE | Matco Tools List: $31.95
(0) LARGE ADJUSTING YOKE
4534A-5

Part of MST4534A. View Details

MEDIUM SIZE JAW SET | Matco Tools List: $27.95
(0) MEDIUM SIZE JAW SET
4534A-9

Part of MST4534A. View Details

SHORT JAWS | Matco Tools List: $27.95
(0) SHORT JAWS
4534A-10

Part of MST4534A. 2 count. View Details

1/2" COLLET/PIN ASSEMBLY | Matco Tools List: $45.95
(0) 1/2" COLLET/PIN ASSEMBLY
4581A-4

Part of MST4581A. Double thread forcing screw. View Details

UNIVERSAL WIPER ARM PULLER | Matco Tools List: $189.95
(0) UNIVERSAL WIPER ARM PULLER
WAP1422

For pulling tight-fitting, rusted and deep-set windshield wiper arms on VW, Audi and many European/American cars. Windshield wiper arms can be pulled without removing the hood of the vehicle. The threaded spindles are guided by a movable bushing, which allows the puller to be fitted to the edge of the arm at the start and in the middle of the removal process... View Details

5 TON INDEXING GEAR PULLER | Matco Tools List: $203.95
(0) 5 TON INDEXING GEAR PULLER
MST5T

Jaws are made of CR-MO, and the unit is chrome finished. Center screw is made of carbon steel that is black oxide finished - 8.5" in length. Leg's indexing-jaw design allows legs to index into position and stay in place, allowing you to support the puller and quickly connect each jaw one at a time to the pulley without help... View Details

MEDIUM UNIVERSAL 2 AND 3 JAW PULLER SET WITH NARROW QUICK ADJUSTING JAWS | Matco Tools List: $1,001.95
(0) MEDIUM UNIVERSAL 2 AND 3 JAW PULLER SET WITH NARROW QUICK ADJUSTING JAWS
K203010S

Made in Germany. 8-in-1 set. For automotive, light truck, etc. use... View Details

CUMMINS ISX GEAR PULLER | Matco Tools List: $154.95
(0) CUMMINS ISX GEAR PULLER
CM369

Used to pull the injector and valve cam gears on Cummins engines (2007-2017) . Comparable to Cummins #3163069. View Details

CHRYSLER/GM/FORD UNIVERVAL HARMONIC PULLEY PULLER | Matco Tools List: $272.95
(0) CHRYSLER/GM/FORD UNIVERVAL HARMONIC PULLEY PULLER
MST9740E

Removes the harmonic damper pulley on most Ford, GM and Chrysler vehicles. Designed for engines with 3- and 6-spoke harmonic damper pulleys. Includes 6 different length push rods & special Patent Pending tip for different engine designs... View Details

2/3 JAW 2 TON PULLER | Matco Tools List: $94.95
(0) 2/3 JAW 2 TON PULLER
P1023

Removes and installs gears, bearings and pulleys on autos, trucks, agricultural and construction equipment. 2 or 3 jaw, 2-ton capacity. 3-3/8" reach and 4-3/4" spread. View Details

UNIVERSAL WIPER ARM PULLER | Matco Tools List: $190.95
(0) UNIVERSAL WIPER ARM PULLER
WAP1421

For pulling tight-fitting, rusted and deep-set windshield wiper arms on VW, Audi and many European/American cars. Windshield wiper arms can be pulled without removing the hood of the vehicle. The threaded spindles are guided by a movable bushing, which allows the puller to be fitted to the edge of the arm at the start and in the middle of the removal process... View Details

HEAVY-DUTY U-JOINT PULLER | Matco Tools List: $303.95
(1) HEAVY-DUTY U-JOINT PULLER
MST5190B

Provides the strength to disassemble even the toughest U-joints in minutes on virtually all Class 7 and 8 trucks and machinery. For use with up to 1" impact tool or air tool. Will not damage the driveshaft, bearings, yokes or bearing cups... View Details