Showing 1 - 7 of 7
Features & Benefits
- HIGH-CONTRAST DISPLAY. Bright 6,000 Count Negative LCD Display that's easy to read inside or outside the shop
- PRECISE READINGS. True RMS Accuracy ensures precise readings on non-sinusoidal or distorted signals
- HYBRID AND EV SAFE. Certified with CAT IV 600V / CAT III 1,000V safety ratings.
- QUICK RESULTS. 60-segment analog bar graph provides fast visual feedback for signal fluctuation
- ACCURATE MEASUREMENT. Low impedance (LoZ) mode helps eliminate ghost voltage readings and measures true voltage on a circuit
- DUAL DISPLAY CAPABILITY. Allows AC voltage or current and frequency to be viewed simultaneously, increasing efficiency during real-time diagnostics
- VERSATILE READINGS. Continuity and diode testing
- MULTI-MODE. Min/Max/Hold/Relative modes for capturing and comparing measurements
- AC/DC Voltage: 0.01mV - 1000V
- AC/DC Current: 0.1uA - 10A
- Resistance: 0.1Ω - 50MΩ
- Frequency: 0.001Hz - 60MHz
- Duty Cycle: 0.1% - 99.9%
- Capacitance: 0.001nF - 60mF
- Temperature: -40°F to 1,832°F
Features & Benefits
- Bright 4,000 Count Negative LCD Display that's easy to read inside or outside the shop
- True RMS Accuracy ensures precise readings on non-sinusoidal or distorted signals
- Hybrid and EV Safe. Certified with CAT IV 600V / CAT III 1,000V safety ratings.
- Continuity and Diode Testing
- Min/Max/Hold/Relative modes for capturing and comparing measurements
- Non Contact AC Voltage Detection
- AC/DC Voltage: 0.1mV - 1000V
- AC/DC Current: 0.1uA - 10A
- Resistance: 0.1Ω - 40MΩ
- Frequency: 0.001Hz - 5MHz
- Duty Cycle: 0.1% - 99.9%
- Capacitance: 0.01nF - 4mF
Features & Benefits
- Voltage: AC 600V DC 600V
- Current: AC 80A DC 80A
- Display 4000 counts
- Jaw Opening 24mm/0.9”Auto & Manual RangingAuto Power Off
- Non-Contact Voltage Detector
- Diode Open Voltage 3.2V
- - Continuity Buzzer <lt/>50Ω
- Data Hold
- Large LCD Display Backlight
- Work Light
Features & Benefits
- WIDE RANGE OF READINGS. Provides readings for volts, amps and ohms required for automotive electrical system tests
- CLAMP JAWS FOR EASY MEASURING. Handy 35mm AmpTip clamp jaws ergonomically measure at jaw tip for small sized conductors up to 60A and regular current, and Hz measures at jaw center for regular conductors up to 600A
- PROFESSIONAL DIGITAL MULTIMETER. Records max, min and calculates average readings over time
- ALL IN ONE DEVICE. Features many different modes to measure what you need, including peak-RMS mode, relative mode, auto-ranging and more
- PRECISE MEASUREMENT. Smallest measuring range: 60A with measurement down to 10mA (reading below 100mA is unspecified)
Features & Benefits
- WIDE RANGE OF READINGS. Professional digital multimeter provides readings for volts, amps and ohms required for automotive electrical system tests as well as diode and continuity tests
- GHOST VOLTAGE BUSTER. Lo-Z ghost voltage buster drains ghost voltages leaving only hard signals on meter readings
- AUDIBLE WARNING FOR SAFETY. Beep-Jack audible warning beeps against improper A-terminal plug in and decreases the risk of damage
- DCV and ACV: 0.1V - 1,000V
- DCA and ACA: 0.1 mA to 8A (15A for 30 sec. max with 5 minutes cool down interval)
- Ohms: 0.1 to 60M
- Line level frequency: 10.00Hz to 10.00kHz
- Logic level frequency: 5.00Hz to 1.000MHz
Features & Benefits
- ACCURATE PROFESSIONAL READINGS. Digital multimeter provides readings for volts, amps and ohms required for automotive electrical system tests, as well as diode and continuity tests
- AUDIBLE WARNING FOR SAFETY. Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
- DCV and ACV: 0.01mV - 1,000V
- DCA and ACA: 0.1 mA to 8A (15A for 30 sec. max with 5 minutes cool down interval)
- Ohms: 0.1 to 60M
- Line level frequency: 10.00Hz to 10.00kHz
- Logic level frequency: 5.00Hz to 1.000MHz
Features & Benefits
- WIDE RANGE OF READINGS. Advanced digital multimeter provides readings for volts, amps and ohms required for automotive electrical system tests as well as diode and continuity tests
- Selectable 4-stroke or 2-stroke DIs for RPM functions
- Selection of 1 to 12 cylinders for dwell and IG-RPM readings
- Fuel injection detector tests both TBI and PFI engines with user-selectable sensitivities
- Performs inductive pickup RPM test on spark plug ignition HV wires
- Dwell-angle and % duty tests conventional engines with user-selectable sensitivities
- Hz of line level voltage measures noisy high voltage ACV frequencies
- +/- trigger polarity for user-selectable readings
- Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
- DCV and ACV: 0.01mV - 1,000V
- DCA and ACA: 0.1 mA to 10A (6A continuous, 10A for 30 sec. with 5 minutes cool down interval)