Showing 1 - 24 of 28
Features & Benefits
- SCREW-IN DESIGN. Allows you to effortlessly re-pack bearings with just a few rotations, no need to push down or step on like with other models
- AUTO-CENTERING DRIVER. Pushes bearing against piston, flushing out old grease and re-packing it uniformly with fresh grease
- EASILY VIEW GREASE LEVEL. Clear, impact-resistant cup allows for grease level visibility
- GREASE FITTING. Features grease fitting for easy grease refill
- Fits bearings up to 3-1/2" O.D.
- Rubberized base
Features & Benefits
- BUILT TO LAST. Designed and constructed to provide the ultimate strength and durability
- THE RIGHT TOOL FOR THE JOB. Easily install bearing cups of Spicer SPL 140, 170, and 250 series U-joints into full-round yokes to the manufacturer’s specifications
- VERSATILE USE. Press plate and quick-change adapters maintain proper specs during the installation for each size bearing cup
- SAFETY ORIENTATED. Provides a safer alternative to less effective makeshift methods that can often lead to component damage or injury
- ACCURATE INSTALLATION. Accurately install bearing cups in minutes on Dana/Spicer SPL life series quick disconnect U-joints
- DAMAGE REDUCTION. Reduce the risk of damage to the driveshaft, yoke and joints
- For use with hand or with air tools
- 1-1/4" Head on the forcing Screw
Features & Benefits
- 6" steel cone cylinder with an integrated bearing in its base nesting in an 8.5" heavy base to allow a technician to place the hub on the tip of the cone to rotate the hub with one hand while applying heat from an oxyacetylene torch
- While rotating the hub, the oxyacetylene torch will raise the temperature of the inner bearing race evenly and quickly a few hundred degrees causing the race to expand and release from the hub due to its tight tolerance
- Allows the technician to easily remove the interference fit instead of trying use a grinder and or chisels to break hardened steel as well as using bearing splitters under extremely high pressure
- Allows the technician to replace the bearing assembly fora fraction of the cost in about 5 minutes versus the traditional 30-45 minutes
Features & Benefits
- Internal magnetic end to hold bearing cup
- Install bearing cups without the use of a hammer eliminating frustrating dislocation of needle bearings, while also protecting surrounding vehicle components
- Install two bearing cups in one procedure on virtually all light and medium-duty U-joints
- Manufactured from high-grade steel for strength and durabilit
- 5-5/8" spread
- 11.50" x 1.85" x 5.17"
Features & Benefits
- For installations on bolt-retained bearing cups
- Install bearing cups without the use of a hammer eliminating frustrating dislocation of needle bearings, while also protecting surrounding vehicle components
- Outside guide bolts are designed to ensure the bolt-retained bearing cup is accurately aligned for installation.
- Reduces the risk of damage to needle bearings
- Applications include Spicer driveline series 1610 to 1880
- 5.5" x 1.75" x 2.58"
Features & Benefits
- The slide hammer and pull set is designed to remove stubborn bushings, seals, sleeves, bearings, bearing races, bronze, Oilite bushing and pressed-in studs
- The adapters make the slide hammer and puller set ideal for pulling dents in auto bodies
- All parts are hardened to increase strength
- Spiral and Fluted Screw Extractor made of 35Crmo
- Most components made from 40CR Steel for strength
- 3/8-16" threaded slide screw
- Inside spread from 3/8" to 1-1/4"
- Outside spread from 0" to 3"
- A maximum reach of 2-1/2"
- HRC 40-45
- Includes sizes: 2 lb. slide hammer and slide rod, screw adapter, square hook, jaw adapter, 2 jaw puller with large and small jaws, puller hook, locking pins, T handle crossbar, fluted extractor and bonus spiral extractor
Features & Benefits
- Remove and insert bushings in cars, trucks, buses, tractors, construction and off-road equipment
- Sizes range from 1-5/16" to 1-7/8"
- Includes 7 bushing adapters and 1 driver
- Hardened alloy driver and chrome plated bushing adapters for maximum tool life
Last Chance
Features & Benefits
- Includes small, medium and large drivers and bushing adapters from 3/8" to 1-3/8"
- Perfect for removing and inserting bushings in cars, trucks, buses, tractors, construction and off-road equipment
- Hardened alloy drivers and chrome plated bushing adapters for maximum tool life
Features & Benefits
- 42mm 12-point 1/2" drive socket
- For late model Ford 42mm pinion nuts and many other uses
Features & Benefits
- Quick and precise removal and installation of wheel bearings
- For use on front wheel drive cars and light trucks
- Allows the user to replace wheel bearing with steering knuckle and strut assembly on vehicle
- Save time by not removing assembly from vehicle and no front end alignment after job is complete
- Works on bearings 1.96" to 3.48"
Features & Benefits
- Universal tool set for extracting and mounting silent bearings, hydraulic bearings, ball bearings, rubber bearings, shaft seals, bearing bushes and more
- Sleeves are able to be stacked with the UPPS400 Press and Pull Kit
- When combined with the C-clamp, can be used for ball joints as well
- Kit includes 10 sleeves, 3 spindles and 4 discs
- Sleeves' outer diameters: 24 - 42mm, 15/16" - 1-21/32"
Features & Benefits
- Makes the UPPS399 into a UPPS400 kit
- Kit includes: 12 sleeves and 2 spindles
Features & Benefits
- All-in-one design eliminates the need for a driver with different sized adapters
- Locking screw holds the jaws in place for one hand use
- Steel striking end and aluminum anodized head
- Adjustable from 3/4" to 3-1/2"
Features & Benefits
- Most complete package includes: 20 sleeves, 4 discs and "Vibro-Impact" C-clamp
- Universal tool set for extracting and mounting all kinds of bearings and bushings
- For use by hand under the shop press or on the car with the "Vibro-Impact" C-clamp
- *Ceramic lube not included
Features & Benefits
- Heavy-duty truck set fits most class 8 over the road trucks and trailers
- Use the tapered driver side for bearing races; reverse to the flat side for seals
- Set includes 6 sizes and two handles that you can screw together for extra length and a flanged nut to hold the adapters onto the handle
- Bearing race size: 3-43/64" O.D., 4-13/16" O.D., 4-7/8" O.D., 5-25/32" O.D., 5-1/2" O.D. and 6" O.D.
Features & Benefits
- Universal tool set for extracting and mounting silent bearings, hydraulic bearings, ball bearings, rubber bearings, shaft seals, bearing bushes and more
- Inner sleeves are made out of non-hardened metal for easy adjustments or reshaping
- Nuts include bearings to further reduce friction
- Kit includes: 4 step discs, 8 inner sleeves, 2 spindles and 4 nuts with bearings
Features & Benefits
- Easy, adjustable clamping chain for maximum grip
- Drop forged metal for highest quality
- Fits all bearings and sleeves between 40mm and 60mm
- Three arms provide equal gripping power on each side, avoiding tilt
- Edges can be re-sharpened
Features & Benefits
- Universal tool set for extracting and mounting silent bearings, hydraulic bearings, ball bearings, rubber bearings, shaft seals, bearing bushes and more
- Inner sleeves are made out of non-hardened metal for easy adjustments or re-shaping
- Nuts include bearings to further reduce friction
- Kit includes: 4 step discs, 20 inner sleeves, 4 spindles and 8 nuts with bearings
Features & Benefits
- Installer is made of high quality steel and designed with an integral driver handle to provide the weight to drive the seals in easily
- Correctly installs the seal onto the axle shaft and into the wheel knuckle, preventing front hub vacuum leaks that would cause the 4WD to not engage
- Works on 2005-newer Ford F-250, F-350 4X4s having the vacuum-operated front axle
Features & Benefits
- Complete standard and metric bushing adapter set with 30 adapters up to 1-3/8" and 42mm in one set
- Set contains the correct size for the job and provides maximum productivity
- Handles do not extend past bottom of adapter and can be used in blind hole applications without bottoming out the driver
Features & Benefits
- Works on 1998-2004 Ford F-250, F-350, F-450 and F-550 4X4s having the vacuum-operated front axle
- Correctly installs the seal onto the axle shaft and into the wheel knuckle without causing front hub vacuum leaks
- One piece design manufactured from high quality steel
Features & Benefits
- Adapters have a different angle other than standard bearing race and seal drive adapters
- Includes 16" long, two piece, screw-together handle for hard to reach pinion races inside the rear end
- Pneumatic driver and washer included for use with air hammer
- Used to drive pinion bearing races in rear end on '95 and newer Dodge, Ford and GM trucks
- Contains drivers in the following sizes: 2-11/16", 2-27/32", 2-7/8", 3", 3-1/4", 3-1/2", 3-3/4" and 4-1/8"
Features & Benefits
- Inserts wheel bearing race and seals without damage to race axle housing
- 2 driving methods and 11 adapter sizes: 1.565", 1.750", 1.965", 2.325", 2.470", 2.555", 2.83", 2.995", 3.18", 3.813" and 4.625"
- 2 larger sizes for Dana 60/70 and Dana 80 applications to fit 3/4 and 1-ton trucks
- Includes a pneumatic driver and longer handle
- Turn discs over to drive seals
Features & Benefits
- Inserts wheel bearing on first try
- Fits most standard wheel bearing sizes